Operating instructions
Instructions for use
- It is not recommended to persons sensitized to natural latex, dithiocarbamates and thiazoles to use these gloves .
- Put the gloves on dry, clean hands.
- Position the cuff over the garment to prevent skin exposure.
- These gloves are designed for single use only.
- If gloves have been contaminated with chemicals, do not touch the external side of the gloves when taking them off. Fold back the cuff end and pull them off while turning them inside out.
Storage conditions
Store the gloves in their sealed packaging protected from direct sunlight, far from heat sources and electrical equipment
Legislation
- This product is not classified as hazardous according to the directive 1999/45/EC of the European Parliament and of the Council.
- This product does not contain any substances of very high concern according to the regulation n° 1907/2006 of the European Parliament and of the Council (REACH).
Chemical chart
Chemical Product |
CAS # |
BTT (minutes) |
Permeation level |
Standard |
Degradation level |
Rating |
1,1,2-Trichlorotrifluoroethane (Freon TF or Freon 113) 99% |
76-13-1 |
3 |
0 |
ASTM F739 |
NT |
NA
|
2-Propanol (Isopropanol) 99% |
67-63-0 |
3 |
0 |
ASTM F1383 |
NT |
NA
|
4,4'-Methylenedianiline (MDA) 15% and 15% Methanol mixture |
101-77-9 |
2 |
0 |
ASTM F739 |
NT |
NA
|
Acetone 99% |
67-64-1 |
1 |
0 |
ASTM F1383 |
NT |
NA
|
Ammonium hydroxide solution 29% |
1336-21-6 |
19 |
1 |
ASTM F1383 |
NT |
NA
|
Hydrochloric acid 37% |
7647-01-0 |
110 |
3 |
ASTM F1383 |
NT |
NA
|
Methyl Ethyl Ketone (2-Butanone) 99% |
78-93-3 |
NT |
NT |
|
4 |
NA
|
Sodium hydroxide 20% |
1310-73-2 |
480 |
6 |
EN 374-3:2003 |
NT |
NA
|
Sodium hydroxide 40% |
1310-73-2 |
480 |
6 |
EN 374-3:2003 |
NT |
NA
|
Sodium hydroxide 50% |
1310-73-2 |
480 |
6 |
EN 374-3:2003 |
NT |
NA
|
Sulfuric acid 96% |
7664-93-9 |
21 |
1 |
EN 374-3:2003 |
NT |
NA
|
t-Butanol 99% |
75-65-0 |
10 |
1 |
EN 374-3:2003 |
NT |
NA
|
*not normalized result
Overall Chemical Protection Rating
Protection rating is determined by taking into account the effects of both permeation and degradation in an attempt to provide users with an overall protection guideline when using our glove products against specific chemicals.
Used for high chemical exposure or chemical immersion, limited to BTT based on a working day.
Used for repeated chemical contact, limited to total chemical exposure i.e. : accumulative BTT based on a working day.
Splash protection only, on chemical exposure the gloves should be discarded and new gloves worn as soon as possible.
Not recommended, these gloves are deemed unsuitable for work with this chemical.
NT : Not tested
NA : Not applicable because not fully tested (only degradation OR permeation results)
The chemical test data and overall chemical protection rating should not be used as the absolute basis for glove selection. Actual in-use conditions may vary glove performance from the controlled conditions of laboratory tests. Factors other than chemical contact time, such as concentration and temperature, glove thickness and glove reuse, may also affect performance. Other glove requirements, such as length, dexterity, cut, abrasion, puncture and snag resistance, or glove grip also need to be considered in making your final selection.